GoControl Light Switch Guide/Troubleshooting
(3-Way switch, Dimmer, Z-Wave Switch)
This page provides information on the 3 GoControl light switches that rently offers. This includes the product specifications, basic troubleshooting and a link to the manual for further information regarding troubleshooting and installation.
Go Control Z-Wave Wall Switch:
About the Product:
- Options of replacement trim colors: Black, Brown, Almond and Ivory.
- Allows remote On/Off control of loads connected to the switch and is easily wired in place of standard wall switch.
- Integrates with other Nortek Security & Control Z-Wave enable products.
Specs:
- Max Load: 15 amps (1800 watts) 120 VAC
- Motor: 1/2 HP. Max 120 VAC
- Incandescent: 600W max, 120VAC
- Signal: 908.42 MHz, 9.6kpx or 40 kbps capable
- Range: Up to 100 feet between wireless controller and/or closest Z-Wave device.
- Note to Installers: When installing a Z-Wave 3-Way Light setup utilizing Nortek Security & Control products, you will need a Load Bearing switch (WS15Z-1, WD500Z-1 or WD1000Z-1) and a non-load bearing WT00Z-1. Multiple WT00Z-1 switches can be utilized to control multiple Load Bearing devices. Please refer to the linked Technical Bulletin on Z-Wave 3-Way Light Switch Setup for more information.
Installation:
- See attached Manual: Installation Manual
GoControl Z-Wave Wall Dimmer Switch:
About the Product:
- Allows for remote On/Off control and dimming of connected lights.
- Easily wired in place of standard wired dimmer.
- Integrates with other Nortek Security & Control Z-Wave enabled products.
- Offers replaceable trim in the following colors: black, brown, almond and ivory.
- Has an auto-sense feature for local lamp activation independent of the Z-wave controller status.
Specs:
- Maximum Load: 500 Watts for control of permanently installed lighting fixtures only (Not for control of receptacles)
- Signal (Frequency): 908.42 MHz
- Range: Up to 100 feet line of sight between the wireless controller and/or the closest Z-Wave device
- Input: 120v 15A 60Hz
- Note to Installers: When installing a Z-Wave 3-Way Light setup utilizing Nortek Security & Control products, you will need a Load Bearing switch (WS15Z-1, WD500Z-1 or WD1000Z-1) and a non-load bearing WT00Z-1. Multiple WT00Z-1 switches can be utilized to control multiple Load Bearing devices. Please refer to the linked Technical Bulletin on Z-Wave 3-Way Light Switch Setup for more information.
Installation:
- See attached manual: Installation Manual
GoControl Z-Wave 3-Way Switch/Dimmer:
About the Product:
- Allows remote on/off control and dimming.
- The switch controls no load directly, so it can wired anywhere power is available, without the need for a traveler wire.
- Offers a replaceable trim colors: black, brown, and almond.
Specs:
- Signal (Frequency): 908.42 MHz
- Load: does not directly control a load. Another Z-Wave device is required
- Range: Up to 100 feet line of sight between the controller and/or the closest Z-Wave device
- Network wide inclusion
- Connect up to 5 devices to create virtual 3,4,5,6,7-way operation
- Note to Installers: When installing a Z-Wave 3-Way Light setup utilizing Nortek Security & Control products, you will need a Load Bearing switch (WS15Z-1, WD500Z-1 or WD1000Z-1) and a non-load bearing WT00Z-1. Multiple WT00Z-1 switches can be utilized to control multiple Load Bearing devices. Please refer to the linked Technical Bulletin on Z-Wave 3-Way Light Switch Setup for more information.
Installation:
- See manual: Installation Manual
If you need any additional assistance, please contact Rently support at 888-340-6340.
Comments
0 comments
Article is closed for comments.